Small community elevatorsHandmade children's hydraulic lifting platformReasons for market volatility

How to use hydraulic lifting platform to effectively prevent electric shock by adding leakage protector is very common， and the cost is not high. It is both affordable and safe， and can effectively prevent electric shock.

5The boxes and distribution boxes of the hydraulic lift shall be kept clean and the dust on the electrical equipment shall be cleaned in time.

cSmall community elevatorsThe importance of regular maintenance of the hydraulic lifting platform is the same as that of women who need to use skin care products. Without maintenance at ordinary times， wrinkles， spots and various kinds of aging will come when they are old. Therefore， customers must follow the maintenance manual provided by the manufacturer and strictly follow each maintenance item，Hydraulic lifting table which can effectively delay the aging of the hydraulic lifting platform; Overload and partial load are strictly prohibited during the normal use of the hydraulic lifting platform. Use the platform in strict accordance with the operating instructions in the operating instructions. Do not only work for efficiency and overload，3-story small elevatorGuide rail elevatorExperiment effectively prolongs the service life and simplifies the maintenance.

DArleHow to install and use the bearings of the elevator in the process of the bearing device of the elevator? We can not ensure that the bearing device is in the right position every time. It is inevitable that some devices are not in place or the bearings are offset. Once these problems occur in the device， the clearance between the bearings will become too small， and then the inner and outer rings of the bearings cannot be in the same rotation center. Therefore when installing bearings， it is necessary to use special things， and it is also necessary to use a detector to test the bearing device in the future， so as to ensure the success of the bearing device.

QqHigh-altitude work requires the use of tool bags. The heavier and larger high-altitude work tools should be hung on stable components and cannot be placed at will to avoid the occurrence of high-altitude falling accidents.

Drain all the hydraulic oil in the oil tank， open the oil tank， take out the oil suction filter， wash it and put it back into the oil tank，Hydraulic lifting table and install it in situ. The tank is refilled with new oil.

Loose fixing screws of the motor: the motor fan will make a noise when it rotates. If the screws fixing the motor are loose， coupled with its own vibration， the motor will collide with other parts so it will make a noise; The joints of each pin shaft are dry， and the hard friction between iron parts and iron parts not only damages the parts but also makes abnormal noise. Therefore lack of lubricating oil， the small editor should emphasize again， pay attention to timely maintenance and frequently add lubricating oil; The hydraulic lifting platform does not riseIf there is air in the hydraulic oil when the pressure lifting platform does not rise， open the vent hole， and then tighten it after the air is discharged; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: check whether there is oil leakage at each oil pipe interface. If there is oil leakage， replace it in time; Motor reverse: check whether the wiring is wrong; (If you do not understand the electricity， contact the manufacturer of the hydraulic lifting platform in time)

kTime has not spared，Hydraulic lifting table so is the hydraulic lifting platform? With the increasing use time of the hydraulic lifting platform， there will be phenomena in the hydraulic system，3-story small elevatorGuide rail elevatorExperiment such as weak lifting， loose oil pipe joints， and noise. In fact， this is a sign that the hydraulic system is aging. The aging of the hydraulic lifting platform directly affects the use effect， so how can we alleviate“ Aging” What about this unavoidable problem?

MThe sinking of the cargo elevator is the phenomenon that the table top falls due to gravity after a certain period of time after rising to the specified position. Of course， so how to solve it? First of all， find out the reason. The following editor summarizes the ultimate solution.

Yoriginal: The rust of spiral elevator is caused by the fact that some manufacturers materials are not stainless steel. If the rust is not serious， sandpaper can be used to polish the rust.

xRThe starting system of the manual hydraulic stacking platform car is divided into pedal type and manual control type，Scissor lift_ Hydraulic lifting table_ Guide rail lift - scissor lift manufacturer which is simple and easy to operate. The model is divided into fixed type and mobile fork， and common leg and straddle leg are available. It is very suitable for the placement and extraction of goods in warehouses and supermarkets.

: The rust of spiral elevator is caused by the fact that some manufacturers materials are not stainless steel. If the rust is not serious， sandpaper can be used to polish the rust.

After careful inspection， it was found that it was mainly caused by two reasons: the loss of hydraulic pressure and the leakage of hydraulic valve or seal.

Project scopezPreparation before the installation of the elevator folding The preparation before the installation of the elevator folding shall carefully prepare the special construction plan for the installation construction， and carry out the safety technical disclosure to the installation personnel.

MThere will be electric brushes in this machine. The parts where the brushes touch each other must be kept clean. The bearings in the machine also need to be checked regularly， especially the bearings should be added with grease regularly. If the grease is not enough， the bearing will be seriously worn during operation， affecting the service life of the machine. There are all kinds of wires and cables in the machine. After a period of use， it is necessary to check the wires and cables. If the wires and cables are damaged， they should be repaired or replaced. We should also regularly check whether the screws at the connection are loose. If the screws are loose， we should tighten them. Some screws must meet certain torque requirements. In the absence of relevant professional equipment， we can go to the maintenance shop to use professional equipment to tighten the screws. We must make the screws meet the corresponding torque requirements.

Performance of manual hydraulic lifting platform: the manual hydraulic platform car is made of high-strength steel， with a reasonable and compact design structure， safe， stable and reliable. It is equipped with a safety valve， a fully sealed oil cylinder， and a manual hydraulic system for lifting and lowering， which is easy to operate. The guide wheel is equipped to save the operators physical strength and protect the load wheel and the pallet load wheel. Unique hydraulic pump design， easy to start， designed to maintain an ideal height for the loading and unloading operation of the assembly line; With the unique design concept， the operator can operate easily and conveniently.

tSmall community elevatorsUnique“ design; Work” The I-shaped steel frame can bear the pressure evenly effectively reduce the torsion of the frame， and has stronger durability.

qEMobile elevator failure analysis Mobile elevator can not lift or lifting force is weak: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Internal leakage of oil cylinder: check or exchange oil cylinder components; Clamping or internal leakage of reversing valve: check or exchange valve components; The oil level is too low and the oil inlet filter is blocked: add enough oil and clean the oil filter. The fuel supply pump has disadvantages: check or replace the pump.

The open adjusting plate base makes it more convenient to clean sundries.