Small second floor elevatorHydraulic mobile lifting platformInvestment and industry remain the focus

The boxes and distribution boxes are usually kept clean， and dust on the electrical equipment should be cleaned quickly.

4Teach you how to select elevator cables. The following two principles should be followed in the selection of elevator cables: good electrical parameters; During the movement of the cable with the elevator， a section of the cable will bend and deform under the action of gravity， resulting in changes in the electrical parameters of the cable such as impedance and distributed capacitance. When the cable with poor quality is deformed under stress， the parameter changes greatly， which will cause impedance mismatch，Products video attenuation increase and signal reflection，Small elevator villaHydraulic lifting tableCome and take you to understand the performance characteristics and application scope which will lead to the reduction of video signal signal-to-noise ratio and video interference. Therefore， widely applicable to high-altitude work in halls and workshops of various industries such as star hotels and large supermarkets. It has lifting balance， easy operation， and can enter the general lobby. It can enter and leave the elevator at will， with less power consumption， no pollution， and no damage to the ground when working. It can be used for wall work and exploration work without dead corners. The single-column aluminum alloy electric elevator is equipped with gantry cross-frame accessories， which is very suitable for the maintenance of theaters， halls，Products churches， etc.

The novice should pay attention to which equipment wears fast when operating the mobile lift: due to the processing and installation of the components of the mobile lift and other aerial work platform equipment， the rough surface of the equipment， the small contact area and uneven load bearing， the equipment will wear. During the operation of mobile elevator and other aerial work platform equipment， and the wear speed is fast.

SBiliary tumorThe sinking of the cargo elevator is the phenomenon that the table top falls due to gravity after a certain period of time after rising to the specified position. Of course mobile elevators and other aerial work platform equipment are prone to wear and tear of parts and components during the running-in period， this problem must be abnormal， so how to solve it? First of all， find out the reason. The following editor summarizes the ultimate solution.

PcThe heavy operating rod mechanism of the operating rod has defects. Check adjust and replace unqualified parts; Clean the valve; Check the clamping of the hydraulic oil cleanliness valve core (manufacturing， installation and dirt problems)

Regularly add lubricating oil to maintain the lift: during the use of the lift，Products the friction between various components is also relatively large due to the heavy load， especially the lift chain and the lift pivot pin. It is necessary to ensure that the appropriate amount of lubricating oil is added before each use to ensure that the operation is flexible and not blocked. If the elevator is running，Small elevator villaHydraulic lifting tableCome and take you to understand the performance characteristics and application scope once“ appears; Squeak” It can be basically concluded that the friction noise is due to the lack of lubricating oil in the elevator. It is necessary to stop working immediately and find out the reason. It is easy to cause unpredictable hidden dangers. Point summary: it is not allowed to add lubricating oil regularly to maintain the elevator.

At this time， if the aerial work platform is overloaded， it may cause damage to parts and produce some mechanical failures.

mThree-pillar aluminum alloy elevator: three groups of mast-supported operating platforms lift synchronously， with super load capacity and working stability. The integral lifting guardrail device has good strength， greatly reduces the height of the whole machine during transportation， and is very convenient for loading and unloading. The assembly or disassembly can be completed through one lifting.

AHow to solve the problem of oil pipe leakage due to the sinking of the elevator? It may be that the seal is damaged， or the oil pipe has cracks， which leads to the pressure drop and cannot be lifted to a large height.The directional valve is designed to prevent oil return. If there is a problem，Scissor lift_ Hydraulic lifting table_ Guide rail lift - scissor lift manufacturer there will be some backflow， so it can be replaced at this time.

TreformThe oil condition of each system of the elevator shall be checked， and the oil shall be replaced in time in case of foaming and turbidity.

kGThe load of goods and the tonnage of goods transported at one time also affect the speed of lifting and lowering. Achieving the excellent value of goods transported by the lifting platform is the guarantee of speed. If the goods are too heavy， it will affect the speed. If the goods are too light， it will also affect the normal delivery time.

The contact opening and closing of the travel switch of each safety device must be reliable， and the contact crater should be polished in time.

The motor is the core part of the hydraulic lifting platform， and the maintenance of the motor is undoubtedly equivalent to half the service life of the hydraulic lifting platform， so how to properly maintain the motor of the hydraulic lifting platform? Lets share it with users today!

Supply chain quality managementmNovice operation: because novices do not know much about mobile elevators and other aerial work platforms， or do not understand the operation mode， it is easy to cause equipment failure due to operation errors. Operators in this field need to learn patiently and can only operate after training.

HThe guideway elevator installed outdoors is often exposed to rain and sun， so special attention should be paid to regular maintenance and inspection to avoid accidents.

What are the safety tools explosion-proof valves on mobile elevators? They are often seen in large hydraulic equipment， especially heavy equipment. The main effect is to avoid the problems of equipment caused by oil circuit cracking or excessive oil pressure. The installation of small elevator explosion-proof valves depends on the needs of customers， but large equipment basically needs to be installed.

wSmall second floor elevatorThe hydraulic lifting stage roller， ball， large bearing capacity， stable lifting， easy installation and maintenance， and is an economic and practical ideal cargo conveying equipment for replacing elevators between low floors. The editor will tell you about the daily maintenance of the elevator: when the personnel enter the elevator to work， they must hang the elevator to prevent the elevator from suddenly falling and causing casualties.

The routine maintenance of guideway lifting equipment should pay attention to regular inspection and maintenance， eliminate hidden dangers and eliminate faults， which are good for improving work efficiency， extending the service life of the equipment and ensuring the safety performance of the elevator.