Three story small elevatorHydraulic self lifting platformHow to improve the utilization rate of

If the hydraulic valve is damaged， its effectiveness shall be maintained. If it is damaged， it can be replaced in time.

1Matters to be kept in mind when working at heights higher than . meters， many people think that the mechanical strength of the elevator is relatively high， so the installation method in the instruction manual is not strictly followed during the installation process. However， pay attention to the installation precautions corresponding to the working environment，Scissor lift manufacturer and do not be careless. Correct installation，Second floor small elevatorHydraulic lifting table smallWhat are the basic conditions use and maintenance of the elevator is an important link to ensure the normal operation of mechanical equipment. Therefore， when you install the elevator， be sure to carefully assemble and use it in strict accordance with the following installation and use related matters.

When filling hydraulic oil， pay attention to the structure of the oil cylinder. Some oil cylinders are relatively complex inside. How many lifting operations are required to make the hydraulic oil fully transmit to each position during filling， so fill as much as possible during filling， and then test and run the empty machine to see if it reaches the rated position.

VBlanco Castle. High-pressure water abrasive derusting. It is a kind of screw elevator that uses the impact of high pressure water jet and abrasive to polish and remove rust. It has the advantages of little damage to the material， but water has certain damage to electronic equipment. It is applicable to the removable type of screw elevator.

NrThe oil condition of each system of the elevator shall be checked， and the oil shall be replaced in time in case of foaming and turbidity.

Regular inspection and maintenance， elimination of hidden dangers and troubleshooting are good for improving work efficiency，Scissor lift manufacturer extending the service life of equipment and ensuring the safety performance of the elevator.

The heavy operating rod mechanism of the operating rod has defects. Check， adjust and replace unqualified parts; Clean the valve; Check the clamping of the hydraulic oil cleanliness valve core (manufacturing， installation and dirt problems)

aThe configuration of the power unit of the power unit is the key factor affecting the lifting speed. Generally， the higher the power of the power distribution unit， the faster the lifting speed， and vice versa; The solenoid valve of the hydraulic lifting platform of the solenoid valve can be adjusted. Increase or decrease the hydraulic oil flow of the cylinder， and adjust the solenoid valve appropriately， which can also affect the lifting speed.

OThe cleanliness of the hydraulic station is an important aspect of the lift hydraulic station， so it should not be careless. In addition， from a professional point of view，Scissor lift manufacturer there are relevant rules and requirements. You should refer to the specification manual so that you can have a correct understanding and know how to achieve a better cleanliness.

VPriceUse; Put the two lifting cages on the guide rail frame and slowly place them on the buffer spring. Prepare the drive frame of the two lifting cages， and adjust the back wheels and rollers to the position with large clearance to facilitate the installation of the drive frame. Use the lifting equipment to install a standard section for the basic part of the lift and tighten the connecting bolts. Use the lifting equipment to install the two sets of drive frames on the top of the respective lifting cage and put the connecting pins through，Second floor small elevatorHydraulic lifting table smallWhat are the basic conditions and install the cage top guardrail.

yNOutdoor elevator and plant elevator are lifting mechanical equipment. Outdoor elevator is used to transport goods between floors of buildings. Special hydraulic elevator products are mainly used to transport goods between floors; The car lift in the high-rise garage and underground garage. The hydraulic system of the product is equipped with anti-fall and overload protection devices and the operation buttons can be set on each floor and the lifting platform workbench to achieve multi-point.

Check whether all travel switches are loose. If yes， tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; Pin shaft Check whether the pin shaft (ear pin shaft and center pin shaft) is dry. If some are dry， inject corresponding lubricating oil immediately; Check whether nuts， nuts， screws， etc. are loose on site， and if so immediately reinforce them; Ensure that the hydraulic lifting platform lifts smoothly; Outrigger (for aerial work platform)

The novice should pay attention to which equipment wears fast when operating the mobile lift: due to the processing and installation of the components of the mobile lift and other aerial work platform equipment， the rough surface of the equipment the small contact area，Scissor lift_ Hydraulic lifting table_ Guide rail lift - scissor lift manufacturer and uneven load bearing， the equipment will wear. During the operation of mobile elevator and other aerial work platform equipment， the concave and convex parts on the surface of the parts are embedded and friction with each other. The secondary friction between metal debris and the equipment will accelerate the wear of the surface of the equipment parts. Therefore， mobile elevators and other aerial work platform equipment are prone to wear and tear of parts and components during the running-in period， and the wear speed is fast.

AdministrationpThe technical parameters and uses of each type are slightly different， but there are many functions that are similar. Therefore， as a customer， you should have a purposeful choice， that is， what you want to do when you buy a lifting machine， and which lifting machine can meet your needs and use many purposes.

YSafety device of guide rail hydraulic lifting platform The mechanical part of guide rail hydraulic lifting platform mainly includes hydraulic system and mechanical device.

Regularly check whether all mechanisms operate normally and whether there is noise. If any fault is found， it must be eliminated in time.

gThree story small elevatorApplication and characteristics of stage lift: stage lift is also called lifting stage. The stage lift is specially installed on the stage for lifting and rotating the stage. It has a variety of functions such as lifting， and adopts self-locking， interlock， travel switch， mechanical limit， hydraulic explosion-proof and other protective measures.

sRThe motor is the core part of the hydraulic lifting platform， and the maintenance of the motor is undoubtedly equivalent to half the service life of the hydraulic lifting platform， so how to properly maintain the motor of the hydraulic lifting platform? Lets share it with users today!

It seems simple to install the bearing for the elevator， but it is also necessary to pay attention to some details as follows: it is difficult to drive them into the shaft pin when installing the bearing excessively. However， sometimes， some people think of using a hammer to hammer the bearing for the convenience of the device， and use brute force when installing the bearing. In fact， which is the main reason for causing bearing damage and reducing the service life of the bearing. So we must not go too far when installing bearings. Before doing good， put some soft cloth or cardboard on them， and then install them.