+8615628781468
sellelevator@163.com
Based on the data you have investigated， choose the lifting machinery with good cost performance from its technical parameters practicality and versatility. Generally， there are many types of lifting machinery， including (vehicle-mounted， fixed， scissors，Hydraulic lifting table etc.)
1Make sure to add grease twice a month to the transmission assembly where the grease nipple is located for lubrication. For the parts that cannot be added with grease，Small elevator in family roomFixed hydraulic lifting platformKnowledge related to product classification be sure to dredge the oil circuit or replace the grease nipple until the grease can be added， otherwise it is forbidden to use the equipment.
wVilla elevator small elevatorThe oil filter is seriously blocked; The solution is to clean the oil filter or replace the hydraulic oil.
The daily maintenance of the guide rail elevator should ensure that the transmission position where the grease nipple is located needs to be greased twice a month. For the parts that cannot be greased， it is necessary to dredge the oil circuit or replace the grease nipple until the grease can be added， otherwise it is forbidden to use the equipment.
JCotiolahtiWith the progress of the times， the development of science and technology， and the growth of the economy， there are tens of thousands of types of elevators sold on the market. But how to choose mobile lifting platforms? You know， elevators solve some problems of aerial work and provide convenience for aerial work. Now lets follow the editor to see how to choose mobile elevators.
UcRemove and disassemble the lowering valve of the hydraulic elevator， blow the plunger clean with compressed air，Hydraulic lifting table and then install it again.
Talking about the daily maintenance and use of the motor of the hydraulic lifting platform. Overload is strictly prohibited. Overload will increase the burden of the motor and cause the motor to burn out in serious cases.
After the purchase of mobile elevator， it is necessary to check whether the accompanying technical data are complete， whether the accompanying accessories， tools and accessories are consistent with the list whether the equipment and accessories are damaged or defective， and make unpacking acceptance records when the equipment arrives.
sNormally closed valve and motor are powered on at the same time; The solution is correct wiring. When the motor is powered on， the valve is closed and the power is cut off.
LCheck the hydraulic oil quality and level. When the lifting platform is raised to a high level， the hydraulic oil level should be -mm higher than the bottom of the oil tank. When the color of the hydraulic oil becomes dark， the oil is sticky， or there is sand and other foreign matters in the oil， the hydraulic oil should be replaced in time. The hydraulic system of the lifting platform applies # hydraulic oil.
MoriginalSome office buildings and hospitals may need several or even dozens of passenger lifts. In order to increase the speed，Hydraulic lifting table efficiency and area of the electric lift， most high-rise buildings will divide the electric lift into an array，Small elevator in family roomFixed hydraulic lifting platformKnowledge related to product classification each group is responsible for some floors， and make different adjustments and scheduling according to the use mode of different floors at different times.
gAThe second is that steel will have obvious thermal expansion and contraction effect at low temperature. Although the nature of steel will be taken into account when designing and manufacturing hydraulic elevators， after all， the environment is different. At low temperature， steel will have some unstable performance， such as increased hardness and decreased toughness. At this time， more attention should be paid to the maintenance of equipment to keep the key parts lubricated to avoid dry grinding.
First of all， it is necessary to use and operate the elevator correctly，Scissor lift_ Hydraulic lifting table_ Guide rail lift - scissor lift manufacturer and the operators should receive systematic operation training: regular inspection of operation specifications should be carried out， and if any illegal operation of the elevator is found， it should be punished immediately， and the serious cases should be transferred from this post. After the companys experience in elevator production and sales， it is found that most ofOverload use. Although the lift has a large overload capacity in design， the hidden danger caused by such use is very large， and it is easy to cause cylinder roof fall， lift bracket deformation and other injuries. Therefore， the following points should be summarized: the maintenance of the elevator must be equipped with full-time elevator operators who have received on-the-job training， and illegal operation and use are strictly prohibited.
How to install and use the bearings of the elevator in the process of the bearing device of the elevator? We can not ensure that the bearing device is in the right position every time. It is inevitable that some devices are not in place or the bearings are offset. Once these problems occur in the device， and then the inner and outer rings of the bearings cannot be in the same rotation center. Therefore， when installing bearings， it is necessary to use special things， and it is also necessary to use a detector to test the bearing device in the future， so as to ensure the success of the bearing device.
Promise and keep promiseoCheck the front page of the oil pipe， check whether the oil pipe skin of the hydraulic lifting platform is damaged and cracked， and replace it immediately if any; Secondly， check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe. If there is tighten it immediately to avoid oil leakage at the site during the lifting of the hydraulic lifting platform， which may lead to accidents; Before using the hydraulic lifting platform， what items need to be checked to see if the electrical connectors of the circuit system of the hydraulic lifting platform are loose. If yes， please tighten them immediately (note: before touching the electrical wires with your hands， cut off the power supply first to avoid electric leakage and other tragedies)
LThe question of how to prolong the service life of the hydraulic lifting platform is simply discussed here. Many people may not know this kind of equipment， especially which factories are producing this kind of equipment. It is suggested that friends can search online， because many companies selling and producing this kind of equipment now have their own official websites， There is a more detailed introduction about maintenance and maintenance on the Internet. The paint of the elevator is not only a beautiful layer“ Clothing”， More importantlyPaint can insulate the air， avoid the direct contact between steel and air， and slow down the corrosion progress. But there are some common sense that you dont know. Next， let me ask us to explain the tips of anti-corrosion treatment of the paint layer of the lifting channel: choose a reliable brand of paint for the elevator cheap and not greedy. You cant ask for quality， but not for water-bearing hydraulic fluid. Because it is not bound by the conditions of the treatment elevator， but the lift cannot be too large due to the restriction of pickling and phosphating tank; Sand blasting and plastic spraying. The elevator is applicable to all media， but the lifting channel cannot be too large due to the restriction of drying equipment;
Check the hydraulic oil quality and level. When the lifting platform is raised to a high level， the hydraulic oil level should be -mm higher than the bottom of the oil tank. When the color of the hydraulic oil becomes dark， the oil is sticky or there is sand and other foreign matters in the oil， the hydraulic oil should be replaced in time. The hydraulic system of the lifting platform applies # hydraulic oil.
qVilla elevator small elevatorThe main categories of aluminum alloy lifts in the Chinese market are based on the structural form of aluminum alloy lifts. The aluminum alloy lifting platform can be divided into the following categories: single-column aluminum alloy lifting platform， which is light and small， flexible in movement， generally less than meters high， and generally less than kilograms in load， especially suitable for one-person operation.
tUAre there relevant rules and requirements for the cleanliness of hydraulic station?
The load of goods and the tonnage of goods transported at one time also affect the speed of lifting and lowering. Achieving the excellent value of goods transported by the lifting platform is the guarantee of speed. If the goods are too heavy， it will affect the speed. If the goods are too light， it will also affect the normal delivery time.